Misc Oils & Grease

This is a 100cc bottle of Air Cleaner Oil from Kyosho.

This high quality oil helps to keep dirt and debris out of your engine giving you long lasting performance you can count on.


Package includes:

• 1x bottle containing 100cc of oil.

This is a 100 gram pottle of Teflon grease from Ultimate Racing.


Features:

• Teflon grease is used to reduce the friction of plastic gears,
• The gears run cooler and wear less,
• Friction under load is also reduced,
• The Teflon grease from ULTIMATE RACING is viscous and adheres well.

This is the Bearing Blaster from RPM.

Blast away debris from your bearings and extend bearing life with the RPM Bearing Blaster! This simple, two piece tool, works with your favorite cleaning agent, such as Motor Spray, WD-40, electrical contact cleaner, etc. (any cleaner that is pressurized and has a directional spray tube).

The RPM Bearing Blaster has an open, flow through design that eliminates back-pressure problems which also permits more efficient elimination of dirt and grit from the bearings being cleaned.

This tool uses hand pressure to hold the bearing in place during cleaning which means easier access to the bearings and makes cleaning bearings much quicker. By using hand pressure, you will know for sure the cleaning agent is passing through the bearing and not around it.

The Bearing Blaster works with all bearings* with a minimum I.D. of 3mm. and a maximum O.D. 19mm. Standing at a mere 29mm tall and 45mm in diameter, it will be the smallest, most effective tool in your tool box!

No other bearing cleaning method currently available compares to the effectiveness of the RPM Bearing Blaster!

This is a 34 gram tube of Light Curing Putty from Tamiya.

Revolutionary Light-Curing Putty to speed-up finishing time!

• For any busy modeler.
• Putty cures rapidly once exposed to a direct light source.
• Unbelievable curing time.
• The Light-Curing Putty will cure in approx. 1 minute when exposed to direct sunlight, or in approx. 2 minutes under fluorescent light (27W).
• Easy to handle one-component putty.
• The Light-Curing Putty is a one-component putty so does not require any curing agent, realizing very easy usability. Consisting of a smooth paste property, the putty is easy to apply to all surfaces.
• Does not shrink during curing.
• Compared to conventional polyester based putties, the Light-Curing Putty displays almost no shrinking when drying.
• Realizes excellent workability after curing.
• After completely curing, the Light-Curing Putty realizes easy cutting, trimming and filing, ensuring to obtain a smooth surface.
• Can be painted over with plastic paints.
• After curing, the Light-Curing Putty can be easily painted over with plastic paints.
• *Original color: Yellow, Net: 34g (aluminum tube).

This is a 22 gram tube of Fine Polishing Compound from Tamiya.

This paste polishing compound uses extremely fine particles, and accordingly gives a superior level of smooth finish, cleaning up even the slightest of imperfections and giving your paint job a supremely glossy look, and it can be washed away using water when the job is finished.

Great for use before painting, plus on clear or metal parts.

This is a combo package of 4 grams of high quality white silicone grease and 4 grams of black teflon grease from Xceed RC.

High quality white silicone, for use with ball-differentials in electric powered cars, 1/28, 1/24, 1/18, 1/12, 1/10.

Teflon grease: general use / thrust bearings.

This is a tube of Ball Diff Grease from Tamiya.

This is a 10 gram tube of Cera-Grease HG from Tamiya.

This Cera-grease HG is made using Boron Nitride which gives it superior lubrication ability. Cera-grease provides excellent lubrication, and can be used with plastic or metal parts, gears and bearings.

This is a syringe of Slide Bearing Grease from AVID Racing Concepts.

Slide bearing grease provides great protection to your bearing by maintaining lubrication and adding an extra barrier that helps block dust/dirt to reach the deep groove where the ball spins against the rings.

This grease is a light white and capable of performing at temps between -50c to 150c. And guess what, this is the grease that Avid uses in 90% of it's bearings so you are already getting the best grease in your stock bearings and now you can replenish them to make your bearings last longer.

The best thing that separates this grease other then the performance is the syringe that it comes with that makes it so easy to apply. The syringe holds 1/2 oz (6 cc) of grease and ships as pictured minus the ziplock bag which includes a rubber sealing tip.

This is a 4.5ml tube of Shock O-ring Lube from AVID Racing Concepts.

Avid Slop Shock O-ring Lube provides nearly friction-less lubrication for your o-rings and doesn't washout or swell from silicone shock oil.

Specifications

• Won't washout or swell from silicone shock oils.
• Nearly friction-less lubrication for shock o-rings and shafts.
• Provides protection against corrosion.
• Fully compatible in RC temp ranges. -51c to 124c.
• 4.5ml in an acrylic twist cap container.

This is a oiler pen of Teflon based Slip Bearing oil from AVID Racing Concepts.

Avid Slip Bearing Oil will blow you away from the performance gains you will receive by using it. Take our word for it, this is very expensive oil and has been through several 3rd party tests and it isn't even a competition against the other common light oils in the world. This Teflon based oil is designed to reduce metal on metal wear by reducing friction and will remove dirt while displacing other moisture to add protection from rust.

The Slip oiler pen gives easy access to bearings with a 25.4mm steel tip which is protected by the plastic cap. It holds 7.4cc of oil which should last you well over a year of racing.

Oil can be used on wheel and clutch bearings. If you want to prolong the life of a clutch bearing Avid suggests that you blow out the grease of the bearing with an air compressor and use the bearings just like this for the first 1/2 gallon.

This leaves a slight layer of protection to the bearing and then each time you take your motor out to check the clutch shoes, you should wipe down the bearing to remove any dirt collected on the outside and then add 1 drop of Slip Bearing Oil to the bearing before putting back into the clutch.

This is a 8cc tube of Sticky Great Grease from Team Losi Racing.

This is a 10 gram tube of Molybdenum Grease from Tamiya.

This grease consists of Molybdenum disulfide and is ideal to use with R/C gear-boxes.

It’s anti-friction properties ensure your gearbox stays well lubricated and spins freely, maximizing your drivetrain efficiency.

This is a Gear Bag from Tamiya for the DT02 & DT03 buggies and trucks.

Compatible with Racing Fighter, Super Fighter, Sand-Viper, Sand Rover, Neo Falcon, Holiday Buggy, Neo Fighter & Aqroshot.

This is a 30ml bottle of Air Cleaner Oil from Koswork.

This high quality oil helps to keep dirt and debris out of your engine giving you long lasting performance you can count on.


Features:

• Specially developed for high performance engine
• Extra sticky to to stop dirt and dust, but allowing airflow to ensure maximum performance.
• 30ml is good for either a few buggy air filters or quite a few on-road car air filters.

Size: 30ml

Note: Cars, parts, accessories & others are not included.*

This is a 32 gram tube of White Putty from Tamiya.

The currently available Tamiya Putty (Basic Type) has long been praised by modellers for its high quality and ease of use. However, it's gray color sometimes made painting over it with a lighter color difficult. Tamiya now provides modellers with a white-colored putty to solve this problem.

Useful for filling holes and seam lines, this versatile putty can be used on plastic, wood, or metal, and can also be diluted with lacquer thinner for a wide range of applications.

Each aluminum tube contains 32 grams of putty.

This is a 22 gram tube of Coarse Polishing Compound from Tamiya.

This paste polishing compound was developed specifically for use on plastic models.

Relatively large particles - in combination with the paste - are highly effective when smoothing out any rough finishes on your model's surface, and it can be washed away using water when the job is finished.

Great for use before painting, plus on clear or metal parts.

This is a 22 gram tube of Fine Polishing Compound from Tamiya.

This paste polishing compound was developed specifically for use on plastic models.

This paste polishing compound uses small particles for the kind of finely-polished, smooth surface that is required before applying your model's topcoat.

It can also be used to clear up any scratches on transparent parts. and it can be washed away using water when the job is finished.