Tamiya Vintage Cars

• 1/10 scale R/C model assembly kit. Length: 430mm, width: 243mm, height: 157mm. Wheelbase: 275mm.
• The lightweight, durable 0.7mm thick polycarbonate body depicts the form of the Egress - a successor to the famed Avante - with 1.0mm thick polycarbonate wing and under guard.
• Polycarbonate body, wing, etc. require painting with separately sold Tamiya Color paints for polycarbonate.
• This kit also features dark titanium color anodized front/rear damper cylinders and front uprights, plus new color stickers and silver color wheels.
• Required to complete: 2-channel radio, steering servo, ESC, motor, 7.2-7.4volt battery with charger, and Tamiya PS paint.

• 1/10 scale R/C shaft-driven 4WD buggy assembly kit. Length: 420mm, width: 240mm, height: 140mm. Wheelbase: 260mm.
• Carbon-fiber parts such as 2mm thickness upper & lower decks, plus rear damper stay offer superb strength.
• Includes Avante (2011) Racing Steering Set, with a 2mm thickness carbon fiber steering plate and 850 ball bearings giving silky smooth motion.
• Includes Avante (2011) Torque Splitter Set, with torque splitter and ball differentials for sure-footed traction.
• 4-wheel double wishbone suspension has metal shafts for great customizability.
• Aluminum front uprights.
• Spike tires are mounted on fluorescent pink wheels.
• Comes with a 25-Turn motor featuring a special label.
• Requires: 2-Channel Radio, servo, ESC (electronic speed control) 7.2volt battery pack & charger, and Tamiya PS paint.

• Equipped with metal front under guard. Knuckle mechanism is just like that on an actual truck.
• Highly-durable front & rear die-cast metal wheel hubs.
• A planetary gear ensures optimum ratios while a metal dog clutch, shift forks, and plastic gears combine to deliver smooth gear changes.
• Durable, lightweight die-cast aluminium front/rear axle housings are equipped with differentials.
• Power is delivered from the transmission to the front wheels via universal drive shaft.
• An abundance of metal parts is incorporated for a high level of realism.

• 4-Channel radio system
• Servo
• Electronic Speed Controller
• 540 Motor
• Battery
• Charger
• Paint
• AA Batteries for Transmitter

This is a re-release of the iconic Egress 4WD off-road racing buggy.

The Egress first appeared in 1989. It was a follow up kit to the Avante kit, which had a huge fan following. The original Egress featured stacks of special racing parts. The Egress (2013) builds upon the racy original of the same name, adding modern parts to bring it fully up to speed with available battery and motor technologies available in the hobby market today.

Shaft Drive 4WD!
This shaft-driven 4WD chassis features a longitudinally positioned motor and full ball bearings, while carbon fiber upper and lower decks ensure that the model has superb strength. Re-designed front and rear ball differentials offer excellent reliability and easy maintenance, working in tandem with the built-in center one-way to provide sure-footed movement. The one-way bearing is lockable as a set up option. Universal drive shafts feature the same design as those used in the current TRF series parts, to maximize power transmission and improve resistance to wear and tear. 4-wheel double wishbone suspension, supported by four oil dampers equipped with aluminum cylinders, while the front and rear of the model is equipped with stabilizers for enhanced corning performance. Aluminum front uprights offer excellent reliability, and ball bearings in steering linkage arms combine with 2mm thick carbon fiber plate to offer a linear steering response.

Key Features:

• Carbon Fibre Double Deck Frame
• Re-Release of the Iconic 4WD Performance Kit!
• Shaft-Driven 4WD
• Newly-designed ball diffs are employed front and rear, and combine with a center one-way for sure-footed traction.
• The 4-wheel double wishbone suspension is fitted with high-capacity oil dampers for excellent performance off-road.
• The Egress enjoys a wheelbase 15mm longer than that of the Avante, and features carbon fiber upper/lower decks for stability.
• Polycarbonate Body and Under tray
• Front & Rear Ball Differentials + Center One-Way
• 3-Piece Steering Tie Rod
• 4-Wheel Double Wishbone Suspension

What's In The Box?

• (1) 1/10 Egress Off-Road Buggy 4WD Kit
• Polycarbonate Body
• Decal Sheet
• Instructions Manual

• 2-Channel radio system
• Servo
• Electronic Speed Controller
• Motor
• Battery
• Charger
• Paint
• AA Batteries for Transmitter

• 1/10 scale R/C shaft-driven 4WD buggy assembly kit. Length: 420mm, width: 240mm, height: 140mm. Wheelbase: 260mm.
• Carbon-fiber parts such as 2mm thickness upper & lower decks, plus rear damper stay offer superb strength.
• Includes Avante (2011) Racing Steering Set, with a 2mm thickness carbon fiber steering plate and 850 ball bearings giving silky smooth motion.
• Includes Avante (2011) Torque Splitter Set, with torque splitter and ball differentials for sure-footed traction.
• 4-wheel double wishbone suspension has metal shafts for great customizability.
• Aluminum front uprights.
• Spike tires are mounted on fluorescent pink wheels.
• Comes with a 25-Turn motor featuring a special label.
• Requires: 2-Channel Radio, servo, ESC (electronic speed control) 7.2volt battery pack & charger, and Tamiya PS paint.

What's included in the box?
1 x Tamiya Limited Edition Black Special Avante 2011 Off-Road Buggy Kit

• 2-Channel radio system
• Servo
• Electronic Speed Controller
• Battery
• Charger
• AA Batteries for Transmitter

Specifications:
Length: 16.5" (420mm)
Width: 9.4" (240mm)
Height: 4.5" (140mm)
Wheelbase: 10.2" (260mm)
Tread: 7.9" (200mm) distance from wheel centers, left to right
Gear Ratio: 1:8.33
Minimum Ground Clearance: 1.6" (40mm)
Weight: 2.9lbs (1300g)
Length: 13" (330mm)
Width: 5.9" (150mm)
Height: 2.4" (61mm)

• 2-Channel radio system
• Servo
• Electronic Speed Controller
• Motor
• Battery
• Charger
• Paint
• AA Batteries for Transmitter

One of the most popular pick-up trucks of all time, the Toyota Hilux.

Tamiya spared no expense in developing this truck to be the most realistic ever, with a ladder frame chassis and 4WD system just like the actual truck. The 3-speed transmission provides lots of enjoyable driving options and a plethora of metal parts such as the front guard, leaf springs, and aluminum friction dampers make for a very interesting assembly kit.

The large diameter tires provide impressive ground clearance and enhances the realistic resin body's muscular look. Metal-plated parts for the roll bar, front grill, front/rear bumpers, and muffler provide extra detail highlights throughout the model as well.

To top off this unique model, parts for a surfboard are also included.

features:

• Front Styling: Headlights and turn signals can be recreated using separately available LEDs. Maker emblems are recreated with metal-transfer markings.
• Roll Bar Lights: Metal-plated roll bar features 5 light positions, into which LEDs can be installed.
• Front Guard with Fog Lights: Front guard features fog lights, which can be modeled with either light covers on or off.
• Realistic Metal-Plated Wheels: Newly-designed 3-piece 5-spoke wheels feature a stylish gun metal color.
• Rear Styling: Highly accurate injection-molded resin body features lots of metal-plated parts such as the muffler. LEDs can also be installed for realistic taillights.
• 3 Types of Surfboard Markings: Choose from 3 different kinds of markings to create your own custom surfboard
• Metal Leaf Springs: Realistic leaf springs are made from 5 individual panels and can be easily adjusted after assembly.
• Differential: Differential features tough metal diff gears and can be locked to provide awesome off-road ability.
• 3-Speed Transmission: 3-speed transmission provides excellent low speed performance and realistic gear changes. A slipper clutch protects the gears from shocks to ensure smooth operation.

• Length: 508mm
• Width: 216mm
• Height: 270mm
• Weight: Approx. 3.1kg
• Motor: Type RS540
• Drivetrain: Shaft-driven 4WD
• Diff. Gear: Front/Rear 2-bevel Diff
• Suspension: Front/Rear Leaf Rigid
• Dampers: Front/Rear Friction Dampers
• Gear Ratios: 1：64.39 (Low), 1：35.20 (2nd), 1：21.14 (Top)

Tamiya Hilux truck with friction shocks, 540 motor, surfboard,
molded White body, window section, body trim, decals, plastic light
lenses, tires, wheels, 16 tooth pinion gear, 54 tooth spur gear
instructions

Needed To Complete:
 

• 4 Channel Radio and Receiver
• Standard Size Servo for steering and Gear Changing Servo
• ESC which is 540 brushed motor compatible
• 7.2V NiMH Battery with standard Tamiya connector
• Charger for Battery
• Paint and Building equipment

• Transmitter/Receiver
• Servo
• Battery
• Charger
• AA Batteries for Transmitter

Chassis: Bathtub type monocoque
Drive: Four wheel
Motors: Two 540 brushed
ESC: TEU-160BK
Gearboxes: Sealed, equipped with bevel gear differentials
Shocks: Eight plastic body friction (not oil-filled)
Body: Plastic, molded in white with metal plated plastic parts for grille, air intake and bumper
Tires: 6.5" (165mm) diameter, 4.3" (110mm) wide, split vee type tread
Wheels: Chrome plated plastic 2.7" (69mm) diameter, 3.7" (94mm)wide
Steering: Four wheel
Caster: Adjustable, caster/toe-in refers to the angle of the front suspension when viewed from the side of the car in relation to the chassis.
Camber: Non-adjustable

Package Includes:

Super Clod Buster Pickup Truck Kit, two Motors, ESC, Body, Tires, Wheels, Decals and Instructions

Needed to Complete:

• 2 Channel Radio and Receiver
• Standard Size High Torque Servo for steering
• 7.2V NiMH Battery with standard Tamiya connector
• Charger for Battery
• Paint and Building equipment

Specifications:

Vehicle-
Length: 18.9" (480mm)
Width: 14.9" (380mm)
Height: 13.4" (340mm)
Weight: 8.73lbs (3960g)

Body-
Length: 17" (432mm)
Width: 6.8" (173mm)
Height: 4.8" (121mm)

1. Same 2WD chassis as used for ITEM# 58354 The Frog, with 4-wheel independent suspension and full ball bearings to handle tough off-road driving.
2. Comes with two body shells, one made of plastic material similar to the original BRAT for a nostalgic feel and one made from durable polycarbonate material (included).
3. Type 540 motor included.
4. Electronic Speed Control Unit (TBLE-02S) also included.

1. Improved re-release model of the subaru brat, which made its debut in 1983
2. Lightweight and durable abs space frame
3. Four wheel independent suspension
4. Differential gear for smooth cornering
5. Includes both realistic resin and lightweight polycarbonate bodies
6. Requires a 7.2V running battery (not included)
7. Requires a 2ch. radio control system
8. Model may vary from image on box
9. Use Tamiya color for painting resin body and Tamiya polycarbonate color for polycarbonate body (paint not included)

1. Transmitter/Receiver
2. Servo
3. Battery
4. Charger
5. AA Batteries for Transmitter
6. Paint

• Front double wishbone and rear trailing arm setups are cushioned by high-performance CVA oil dampers.
• Space frame chassis incorporates a dust cover part to ensure that vital R/C equipment is protected.
• Universal drive shafts not only boost efficiency; they also minimize the risk of popping out when driving.

• Transmitter/Receiver
• Servo
• Battery
• Charger
• AA Batteries for Transmitter

• Transmitter/Receiver
• Servo
• Battery
• Charger
• AA Batteries for Transmitter

• Scale: 1/12
• Length: 400mm
• Width: 168mm
• Height: 139mm
• Wheelbase: 256mm
• Weight: 1,800g
• Type 540 Motor
• Rear-Wheel Drive
• Tire Width/Diameter: (F/R) 29/77mm
• Tread (F/R): 138mm
• Duralumin Frame Chassis
• 3-Bevel Differential
• 2-piece Steering Tie-Rod
• 4-Wheel Double Wishbone Suspension with Metal Torsion Bar Springs
• Gear Ratio=9.3:1, 16:1, 21:1

• Transmitter/Receiver
• Servo
• Battery
• Charger
• AA Batteries for Transmitter
• Paint

• Transmitter/Receiver
• Servo
• Battery
• Charger
• AA Batteries for Transmitter

This R/C model assembly kit is a re-released and updated version of the 4WD buggy Hotshot II, the original of which was first released in 1987. The sleek, smart body and rear wing are polycarbonate and pre-painted black, as well as being pre-cut. Stickers are included to apply racy orange and yellow markings.

Durable 4WD Buggy Chassis
The Hotshot II has a shaft-driven 4WD chassis with sealed gearboxes front and rear to keep out dirt and sand; each has a differential inside for smooth cornering, while the underside of the model is protected by the underguard. Its 4-wheel independent double wishbone suspension employs three CVA oil dampers - one at the front and two at the rear, with a front stabilizer helping to get the most out of the 4-wheel drive. White dish design wheels are paired with semi-pneumatic oval block tires for exemplary grip on tough off-road surfaces.

Features include:

• The Hotshot II wedge body design is a classic!
• Red front upright parts really catch the eye.
• The front monoshock suspension uses a single CVA oil damper, which artfully keeps chassis roll in check.
• The metal roof has an integrated air intake, while a driver figure is included to use in the cockpit.
• The rear uses H-shaped arms top and bottom. Dog bone drive shafts are a reliable design.
• Each rear wheel has a CVA oil damper, which help the Hotshot II pick its way across challenging off-road surfaces.
• Dish wheels are of a different width front and rear, each with its own size of oval block tire.
• Like the body, the rear wing is pre-painted black polycarbonate, pre-cut for your convenience!

Specifications:

• Length: 390mm
• Width: 235mm
• Height: 160mm
• Wheelbase: 265mm
• Tire width/diameter: 31/88mm (front); 38/88mm (rear)
• Tread: 205mm (front); 200mm (rear)
• ABS monocoque frame
• Shaft-driven 4WD
• 3-bevel differential gears
• 2-piece steering tie-rod
• 4-wheel independent double wishbone suspension
• CVA oil dampers
• Selectable gear ratio = 10.04:1, 8.70:1, 8.16:1, 7.68:1
• Type 540 motor
• Electronic speed controller (ESC) is sold separately.

What's In The Box?

• 1/10 Hotshot II Off-Road Buggy 4WD Kit
• Painted Polycarbonate Body
• Decal Sheet
• Instructions Manual

• 2-Channel radio system
• Servo
• Electronic Speed Controller
• Battery
• Charger
• AA Batteries for Transmitter

Hit for Six
1976 saw the dawn of the P34, Tyrrell's wonderfully inventive six-wheeled car with four smaller front wheels, that backed up its looks with solid results such as an impressive one-two finish for the team at the 1976 Swedish GP. At the 1977 season-opening Argentine GP, the P34 had a fully-cowled body adorned with a blue and white livery and First National City bank as a sponsor; that car is recreated by this 1/10 scale R/C model assembly kit. The body is injection molded in detailed yet durable plastic, with upper cowl sections molded in white and side pontoons in blue. Stickers are included for depiction of either of Peterson's number 3 or Depailler's number 4 cars, complete with Goodyear tire logos - just apply the stickers, and the body is ready!

Special 6-Wheeled F103 Chassis
The high performance direct drive 2WD chassis utilizes a semi double deck frame with 1.5mm thick upper and 2.5mm thick lower FRP plates. Kingpin coil spring 4-wheel independent front suspension consists of the one-piece lower arm and individual left/right upper arms. One servo controls the steering of all four front wheels. The rear suspension features a rigid T-bar with coil spring and low-friction pads. The spur gear has a built-in ball diff for limited slip effect. Grippy sponge tires masterfully harness the power provided by the motor.

Key Features:

• The body is injection molded in white and blue to realistically depict the Tyrrell P34 1977 Argentine GP version
• The 6-wheel F103 chassis is equipped with friction dampers that allows for high-speed running despite its 2WD design
• Small front and large rear tires are high-grip sponge type
• RS-540 Sports Tuned Motor (TAM53068) is included

What's In The Box?

• Tamiya 6 Wheeler Kitset
• Body Shell
• Decal Sheet
• Instruction Manual

Required for Operation (Not Included)

• 2-Channel Radio set
• Steering Servo
• Electronic Speed Controller
• 7.2V Battery for Chassis
• Compatible Charger

• This R/C model assembly kit is a re-released and updated version of Thunder Shot, the original of which was first released in 1987. 
• Polycarbonate body is pre-cut & pre-painted in white and blue, with transparent canopy. (Body requires application of stickers, assembly and painting of figure, and other work.)
• ABS bathtub chassis.
• 4-wheel independent double wishbone suspension with CVA oil dampers uses front stabilizer for a superior ride. Kit includes CVA oil dampers II instead of Type I seen in the original release.
• The front and rear sealed gearboxes contain compact, durable die-cast 3-bevel differential gears for smooth performance.
• Semi-pneumatic spike tires.
• Contains separate rear wing (pre-painted in white).
• Includes a driver figure.
• Type 540 motor and ESC included.

• 2-Channel radio system
• Servo
• Electronic Speed Controller
• Battery
• Charger
• Paint
• AA Batteries for Transmitter

• Adjustable Gear Ratio Fixed
• Bearings Plastic bushing
• Body Material ABS Plastic pre-painted body
• Body Stickers Pre-Applied
• Chassis Material ABS Plastic
• Construction Type Expert-Semi-Assembled
• Differential Type Gear
• Drive Type 2WD
• Electronic Speed Control (esc) Included TEU-105BK ESC
• Motor 540-brushed type
• Scale 1/12
• Shock Damper Friction type
• Suspension Independent front/solid axle rear
• Terrain Use Multi-Purpose

• Transmitter/Receiver
• Steering servo
• Battery
• Charger
• AA Batteries for Transmitter

• Adjustable Gear Ratio Fixed
• Bearings Plastic bushing
• Body Material ABS Plastic pre-painted body
• Body Stickers Pre-Applied
• Chassis Material ABS Plastic
• Construction Type Expert-Semi-Assembled
• Differential Type Gear
• Drive Type 2WD
• Electronic Speed Control (esc) Included TEU-105BK ESC
• Motor 380-brushed type
• Scale 1/10
• Shock Damper Friction type
• Suspension Independent front/solid axle rear
• Terrain Use Multi-Purpose

• Transmitter/Receiver
• Steering servo
• Battery
• Charger
• AA Batteries for Transmitter

• Adjustable Gear Ratio Fixed
• Bearings Plastic bushing
• Body Material Polycarbonate pre-painted body
• Body Stickers Pre-Applied
• Chassis Material ABS Plastic
• Construction Type Expert-Semi-Assembled
• Differential Type Gear
• Drive Type 2WD
• Electronic Speed Control (esc) Included TEU-105BK ESC
• Motor 540-brushed type
• Scale 1/10
• Shock Damper Friction type
• Suspension Independent front/solid axle rear
• Terrain Use Multi-Purpose

• Transmitter/Receiver
• Steering servo
• Battery
• Charger
• AA Batteries for Transmitter

• Adjustable Gear Ratio Fixed
• Bearings Plastic bushing
• Body Material ABS Plastic pre-painted body
• Body Stickers Pre-Applied
• Chassis Material ABS Plastic
• Construction Type Expert-Semi-Assembled
• Differential Type Gear
• Drive Type 2WD
• Electronic Speed Control (esc) Included TEU-105BK ESC
• Motor 540-brushed type
• Scale 1/12
• Shock Damper Friction type
• Suspension Independent front/solid axle rear
• Terrain Use Multi-Purpose

• Transmitter/Receiver
• Steering servo
• Battery
• Charger
• AA Batteries for Transmitter

• Transmitter/Receiver
• Servo
• Battery
• Charger
• AA Batteries for Transmitter

• Transmitter/Receiver
• Servo
• Battery
• Charger
• AA Batteries for Transmitter

• Transmitter/Receiver
• Servo
• Battery
• Charger
• AA Batteries for Transmitter

• Transmitter/Receiver
• Servo
• Battery
• Charger
• AA Batteries for Transmitter

• Adjustable Gear Ratio Fixed
• Bearings Plastic bushing
• Body Material ABS Plastic
• Body Stickers Included
• Chassis Material ABS Plastic
• Construction Type Assembly Kit
• Differential Type Gear
• Drive Type 2WD
• Motor 380-Brushed Type
• Requires A 2-channel radio, steering servo, 7.2volt battery & battery charger
• Scale 1/10
• Shock Damper CVA Oil Filled
• Suspension Front swing arm and rear rolling rigid suspension setup
• Terrain Use Multi-Purpose

• Transmitter/Receiver
• Servo
• Electronic Speed Controller
• Battery
• Charger
• AA Batteries for Transmitter

• The flowing, dynamic body lines are a real treat; it is pre-painted in white, and pre-cut, just requiring application of stickers.
• A durable, easy-maintenance layout employs a bathtub frame with front and rear gearboxes screw-attached to it.
• Double-wishbone suspension features upper "I" and lower "H" arms, and employs a front stabilizer to minimize roll when cornering.
• CVA oil dampers give exemplary shock absorption that translates into a highly controllable drive.
• An aluminium motor mount not only boosts the model's rigidity, it also helps with motor heat dissipation.
• This image is a close up on the CVA oil damper-fitted rear double wishbone suspension.
• Dish wheels attract less mud when driving; they are paired with grippy spike tires.
• The polycarbonate chassis cover includes a depiction of driver arms. The helmet is a separate part.

• 2-Channel radio system
• Servo
• Electronic Speed Controller
• Battery
• Charger
• Paint
• AA Batteries for Transmitter

• The stylish, streamlined body features distinctive flared sides. It is pre-painted in red and pre-cut for convenience.
• CVA mini oil dampers are employed on the front suspension. A stabilizer helps combat roll in corners for a stable drive.
• A polycarbonate dust cover for the chassis helps protect the innards from the potentially damaging effects of dust and dirt.
• The Fire Dragon's rear suspension also features CVA oil dampers (short type), for smooth and consistent suspension stroke.

• Transmitter/Receiver
• Servo
• Electronic Speed Controller
• Battery
• Charger
• AA Batteries for Transmitter

• Front double wishbone suspension utilizes upper "I" arms and lower "H" arms for a ground hugging drive.
• A front monoshock setup employs a CVA oil damper and helps limit roll when your buggy is cornering.
• A close-up on the aluminum motor mount, which facilitates rigidity and superior heat dissipation.
• The double wishbone suspension setup at the rear employs dual CVA oil dampers for a smooth ride.
• Dish design wheels help mud and dirt to slide right off, and are paired with grippy spike tires.
• A polycarbonate chassis cover provides protection from dirt, and features a driver figure for realism.

• Transmitter/Receiver
• Servo
• Electronic Speed Controller
• Battery
• Charger
• AA Batteries for Transmitter

• 2-Channel radio system
• Servo
• Electronic Speed Controller
• Battery
• Charger
• AA Batteries for Transmitter
• Paint

Specifications:
Length: 400mm
Width: 315mm
Height: 150mm
Wheelbase: 284mm
Tread: 245mm distance from wheel centers, left to right
Gear Ratio: 1:9.33
Suspension: Front Swing Arm, Rear Rolling Rigid

• Transmitter/Receiver
• Servo
• Battery
• Charger
• AA Batteries for Transmitter

• Transmitter/Receiver
• Servo
• Electronic Speed Controller
• Battery
• Charger
• AA Batteries for Transmitter