Team Losi Racing
This hinge brace has been machined from 6mm aircraft grade aluminium, and hard anodized for durability. This plate has been redesigned from the previous version. It is now a solid plate, and eliminates the holes in the brace for greater reliability. This brace set with inserts includes 16 adjustment cams for quick and easy Toe, Anti-Squat, and Kick-Up adjustments.
Features
- Machined from massive 6mm thick aircraft grade aluminium
- Hard anodize coated for long lasting good looks
- Includes 16 adjustment cams for quick and easy Toe, Anti-Squat, and Kick-Up adjustments
- Rear Brace facilitate Toe adjustment from 1-3°, and Anti-Squat from 2-4°
- Quickly change out the adjustment cams for 0.5° increment adjustments
- Adjustment cams are available separately and can be replaced quickly and easily
- Higher roll center for better support in the rear and turn initiation when using stock caster blocks.
Arriving soon - taking pre-orders.
This is a Steer Shaft Sealed Bearing Set from Team Losi, for their new 1/4 Promoto-MX Motorcycle.
The Hard Front Spring Set allows for a firmer suspension feel. The three included springs are only separated by .3 lbs/in increments allowing for very fine tuning to get your TLR Truck dialed in. These firmer springs reduce the roll rate of the front end of the truck, keeping it flatter and allowing it to transition from left-to-right more quickly.
Features:
- Three Pairs of Hard Front Springs 22T, 22SCT and TEN-SCTE platforms
- Paint Markings - Each spring is marked with a paint swatch at the end of the spring for easy identification
- Black Oxide Finish - The black oxide finish works as protection from corrosion
Included Spring Rates:
Softest
- Purple: 4.4 lbs./in
- Brown: 4.7 lbs./in
- Light Blue: 5.0 lbs./in
Packet Includes:
- 2 x 1.4 x 5 tapered hole pistons
- 2 x 1.5 x 5 tapered hole pistons
• This new brass front pivot fits all of the 22 2wd buggies and trucks.
• At +30g heavier than the kit composite front pivot, additional weight over the front axles increases on power steering, but does not pin the car over the front end as the +50g pivot can at times.
• Pivot is the standard height (LRC) and works with the kit kick shims.
• Works with the included aluminum front hinge pin brace (black version) to help improve wear/durability of the front hinge pin holes.
This pivot is +6g heavier than the kit composite front pivot, but still 3g lighter than the previous aluminum pivot. This small increase of weight on the front axles increases the vehicles power steering and durability.
- Anodized Black with silver chamfered edges.
- Pivot is the standard height (LRC) and works with the kit kick shims.
- CNC Machined from durable 7075-T6 Aluminium
- Works with the included aluminium front hinge pin brace (black version) to help improve wear/durability of the front hinge pin holes
Features:
- Turnbuckles are 3.5mm in diameter at the threads for durability
- Titanium is very strong and much lighter than the stock steel turnbuckles
These optional driveshaft bones allow you to move the center differential and motor mount forward in the chassis.
Package includes:
- 1x 61mm driveshaft
- 1x 100mm driveshaft
Features:
- Moves the aluminium faces back 3mm
- Includes servo spacers to properly space all makes and models of servos correctly
- Creates more clearance between the servo and the servo horn, mudguard and body of servo
This optional battery weight set includes 19, 26 and 37 gram weights that are designed to install under the battery, and will add weight down low to help lower the center of gravity.
Packet Include:
- 1 x front gear box halves
- 1 x rear gear box halves
- 2 x rear gear box bearing inserts
The 6.5” wide TLR Medium Downforce Rear Wing provides fantastic grip and stability in all conditions.
Features:
- Made from 1.2mm thick lexan for longer life and has raised end plates for extra tire clearance
- Three scribe lines across the rear offer repeatable wickerbill trimming options
It not only looks great, but it also make removing your receiver easy for when its time to do cleaning / maintenance.
This is a Steel Rear Brake Rotor from Team Losi, for their new 1/4 Promoto-MX Motorcycle.
This is an optional 13T High Endurance clutch bell from Team Losi Racing for their 8IGHT Buggies and Truggies.
Packet includes:
- 2x gold front springs
- 2x silver front springs
- 2x white front springs
Spring Rates:
- White: 3.86
- Gold: 4.13
- Silver: 4.46
These can also be used as a tuning option to add 2mm of track width to the front end.
Includes upgraded metal inserts at pivot points for reduced slop.
These driveshafts will be more durable and provide less friction in the drive line versus the stock dog bones.
This set includes the necessary parts to assemble two complete rear driveshafts, minus grease, which is recommended during assembly.
This is a replacement 775 Motor for the Team Losi Racing 1/8 nitro Starter Box (TLR99059).
These can be used in the front or rear.
Arriving soon - taking pre-orders.
This is a Steel Front Brake Rotor with Screws from Team Losi, for their new 1/4 Promoto-MX Motorcycle.
Arriving soon - taking pre-orders.
This is a Seat and Battery Box Set from Team Losi, for their new 1/4 Promoto-MX Motorcycle.
Arriving soon - taking pre-orders.
This is a Hub Chain Sprocket (Clear) from Team Losi, for their new 1/4 Promoto-MX Motorcycle.
This is a Gold Hub Chain Sprocket from Team Losi, for their new 1/4 Promoto-MX Motorcycle.
This is a Numberless Rider Jersey Set from Team Losi, for their new 1/4 Promoto-MX Motorcycle.
Package Includes:
- 4x Yellow 1/8 Buggy Dish Wheels
NOTE: Do not fit Truggies.
Package includes:
- 2x aluminium hubs
- 2x composite outdrives
- 2x outdrive support rings
- 1x diff nut
Note: These are only compatible with SR aluminium driveshafts. Will not fit standard 22 steel driveshafts.
Packet includes:
- 2 x aluminium bleeder shock caps
- 2 x bleeder screws
- 2 x washers
These driveshaft bones are used in the front/center position.
Does not fit the 8ight-X models
Key Features:
- High-durability aluminium allows inserts to be used for the life of the vehicle
- Hard anodized to improve durability and be resistant against scratching
- Left- and right-side inserts key into gear box to disallow any rotation of the inserts that can cause drivetrain failure
- Laser-etching identification designates inserts for 2.0 gear boxes only
- .1 and .25mm shims included for differential shimming
This set includes the necessary plastic parts to service four shocks.
Arriving soon - taking pre-orders.
This is a 53.6mm Hard Anodized Aluminum Shock Body from Team Losi, for their new 1/4 Promoto-MX Motorcycle.
Constructed from high strength steel these outdrives have been optimized for weight savings without sacrificing durability. These also feature a +1mm length for increase engagement.
Packet includes:
- 1x Left front outdrive,
- 1x Right front outdrive.
Arriving soon - taking pre-orders.
This is a Triple Clamp Set from Team Losi, for their new 1/4 Promoto-MX Motorcycle.
This optional brass ballast weight set will allow you to tune the forward weight bias of your chassis to suit various track conditions and is recommended for carpet track applications.
Package includes:
- 8.8 G heavier than the stock composite part
- Lazer etched for easy identification of kick angle and TLR branding
Package includes:
- 1x 25 degree brass kick shim
This is a packet of (2) Bleeder Shock Caps from Team Losi Racing for use with the TLR 22 family of vehicles up to version 4.0.
These aluminium shock caps will allow you to rebuild your 22 shocks much easier.
Package includes:
- 1x Left Front Arm
- 1x Right Front Arm
Includes upgraded metal inserts at pivot points for reduced slop.
These inserts are made from aluminium and are much stronger, and more rigid over the standard plastic parts.
These inserts are made from aluminium and are much stronger, and more rigid over the standard plastic parts.
This optional brass ballast weight set will allow you to tune the forward weight bias of your chassis to suit various track conditions and is recommended for carpet track applications.
Package includes:
- 2x 25 gram plates that are installed under the electronics
- 1x 14 gram plate that is installed under the servo
- Mounting hardware