Losi 8ight-X Nitro Buggy Parts
These com standard in the front of the Elite version but can be used as an optional upgrade on the standard 8ight-X Kits.
These weights should be secured with the included screws; We recommend also use a small amount of blue loctite to avoid them vibrating loose.
Packet includes:
- 1 x 20g Brass Weight
- 1 x 40g Brass Weight
- 2 x mounting screws
The Punisher body by JConcepts for the TLR 8ight-X Elite is unique. As with all new and popular vehicles on the market, JConcepts wanted to deliver the best looking and performing body shell on the market. Throw everything you know out the window, the Punisher separates itself from the rest of the bodies on the market with its distinctive styling. In the hands of Dakotah Phend, the P1 body shell debuted at the 2020 Southern Indoor Championships.
In the development stage, the P1 was difficult, trying to slick out a design more powerful than the last. However, after fitment, discussion with newly acquired drivers, the form started to take shape. Incredibly low side-pod designs with an ultra-heavy chamfer are traditional looks for JConcepts, however, the power scoops along the cab add some overall muscle to the design, and that gets any racer wired.
The P1 has a broad cab and the placement moves it forward just behind the body mount and front shock tower. The new body was designed to turn and cut through the rough stuff with balance and precision. A centered roof “shark fin” is light and adds, tracking stability and rigidity to the tallest and most pressure sensitive area on the vehicle. Behind the cab, things begin to get interesting with an engine bay roof-top blended into rear kick-up winglets. The rear winglets strike where it gets hot, just behind the engine heat-sink and gives that last bit of downforce area prior to the rear shock tower.
Each P1 body receives window mask, decal sheet and is backed with JConcepts customer support and racing heritage. Performance driven, battle tested – JConcepts is, World Proven Innovation and Design.
Features:
- Original – JConcepts P1 design
- Incredibly low side-pod layout
- Power scoops for added muscle
- Cock-pit “shark fin” for added stability
- Engine bay, roof-top
- Rear winglets for downforce
- Clear polycarbonate with protective film
- Includes window masks and decal sheet
Packet Includes:
- 2 x 1.4 x 5 tapered hole pistons
- 2 x 1.5 x 5 tapered hole pistons
Bearing Kit fits:
- 8ight X
Bearing Kit Includes:
- 6 x 8x14x4 Flanged Revolution Bearings
- 8 x 8x16x5 Revolution Bearings
- 4 x 6x10x3 Revolution Bearings
- 2 x 5x11x4 Revolution Bearings
- 2 x 5x13x4 Revolution Bearings
- 2 x 3/32 X 3/16 X 3/32 Metal Bearings
- 1 x 5x10x4 Metal Clutch Bearings
- 1 x 5x13x4 Metal Clutch Bearings
Packet includes:
- 2x gold front springs
- 2x silver front springs
- 2x white front springs
Spring Rates:
- White: 3.86
- Gold: 4.13
- Silver: 4.46
These can be used in the front or rear.
Packet includes:
- 2 x aluminium bleeder shock caps
- 2 x bleeder screws
- 2 x washers
Packet includes:
- 2x Carbon Rear Arm Inserts
- Required mounting hardware
This wing features a wickerbill design that provides improved air flow and allows you to increase the downforce when needed for various track conditions.
Package includes:
- 1x Yellow wing
- 2x wickerbills
- Required hardware
This wing features a wickerbill design that provides improved air flow and allows you to increase the downforce when needed for various track conditions.
Package includes:
- 1x White wing
- 2x wickerbills
- Required hardware
This wing features a wickerbill design that provides improved air flow and allows you to increase the downforce when needed for various track conditions.
Package includes:
- 1x Black wing
- 2x wickerbills
- Required hardware
Packet Includes:
- 2 x five 1.4mm hole pistons
- 2 x five 1.5mm hole pistons
The stock setup is the 1.4mm pistons up front and the 1.5mm pistons in the rear.
Packet Includes:
- 2 x 1.3 x 8 hole piston
- 2 x "split" pistons that have four 1.3 holes and four 1.2 holes
Avid Triad Titanium Wing Screws are a minimal design approach for securing your wing in 10th scale off/on-road applications. The low profile head is only 1.5mm thick instead of our standard Triad Wing Buttons which are 2.25mm. The OD of the button is also reduced to only 12mm from the standard 16mm which allows the Triad Ti Wing Screw to come in at 0.34g/ea which includes the screw where the standard Triad Wing Button comes in at 0.39g/ea not including the screw.
Features:
- Machined from billet 6Al-4V Titanium
- Designed for 10th scale off/on-road applications with a 6mm long screw
- Low profile 1.5mm screw head
- Screw head is only 12mm instead of the standard 16mm
- Broached with a 2mm allen head on outer side for easy installation and removal
- Weighs 0.34g/ea
Package Includes:
- 2x wing screws
- 1x Avid mini-decal
These screws are used to limit the amount of down travel (droop), on the front and rear suspension arms.
These are used to retain the grease you add to the driveshaft joints, as well as prevent dirt contamination.
Packet includes:
- 4 x axle boots
- 4 x boot retainer rings
- 2x center driveshaft coupler boots
Also fits most other brand Nitro Buggies.
Package Include:
- 340 M3 Screws of various sizes from 6mm to 12mm
- M3 & M4 Washers
- 1 x Handy plastic storage case
Material:
High quality metal material,strengths & durable,ideal for fastening for your rc car.
Compatible with:
Most RC Model Cars,such as Traxxas Slash/Trx-4, Axial SCX10, Arrma, Losi, HPI, Redcat Racing, Exceed RC, HSP, etc.
NOTE: This does not fit the TLR 8IGHT Truggy.
This packet contains all the gears and pins to rebuild one differential.
Packet includes:
- 2x Carbon Front Arm Inserts
- Required mounting hardware
Packet Includes:
- 1 x rear shock shaft
- 1 x piston screw
Packet includes:
- 4 x lower spring retainers
- 4 x 3.5mm shock ends
- 4 x 4mm shock ends
- 4 x lower mounting balls
- 4 x shock end screws
Packet Includes:
- 1 x front shock shaft
- 1 x piston screw
This wing features a wickerbill design that provides improved air flow and allows you to increase the downforce when needed for various track conditions.
Package includes:
- 1x Black wing
- 2x wickerbills
- Required hardware
This package includes six aluminium cross pins, enough for all three differentials, and will help to reduce rotating mass.
Packet includes:
- 1 x 2.2mm front swaybar
- 1 x 2.4mm front swaybar
- 1 x 2.6mm rear swaybar
- 1 x 2.8mm rear swaybar
Note: For the 8IGHT XT Truggy please use TLR242043
TLR EVO shock springs are closer together in rate for finer tuning. They are also constant in coil diameter and longer length when compared to the standard TLR springs. Between the constant coil diameter and the frequency TLR has chosen for these, these handle much better in all conditions, especially when it comes to bumps and landing. These are the orange, 4.0 rate rear springs.
NOTE: There are a couple of changes needed to run these springs on your TLR 8IGHT vehicles. You will need to use the spring cups that come with the shock ends in LOSA5435 that were for the older 1.0 and 2.0 vehicles. You will also need to flip your shock collars over so the lip is on the top.
Note: These turnbuckles are directional and notched for easy thread identification.
Note: These turnbuckles are directional and notched for easy thread identification.
These buttons are 2.5mm thick, feature several highlight cuts, and have the Avid "A" laser etched on the surface, making them an attractive and practical addition to any kit.
Features:
- Aluminium anodized black with machining highlights and the Avid logo laser etched.
- Designed with strength in mind for 8th scale (2.5mm thick, 16mm OD, and cutouts don't go all the way through).
- M3 flat head screw design to fit nearly every 8th and 10th vehicle on the market.
- Comes in Black, Blue, Black/Blue, and Black/Gold.
Includes:
- 2 x Wing Mount Buttons
- 1 x Avid Mini Decal Sheet
By adding nice silver highlights and laser etched logos they are even more desirable. The Triad button is available in a black, blue, red, green, pink, orange, hard anodize, or purple anodized finish and are designed for use with an M3 flat head screw.
Features:
- Aluminium anodized, silver cut highlights, and the Avid logo laser etched
- Minimal weight design, 0.3g/ea
- M3 flat head screw design to fit nearly every 8th and 10th vehicle on the market
- Available in black, blue, red, green, pink, orange, hard anodize, or purple
Includes:
- 2 x Wing Mount Buttons
- 1 x Avid Mini Decal Sheet
By adding nice silver highlights and laser etched logos they are even more desirable. The Triad button is available in a black, blue, red, green, pink, orange, hard anodize, or purple anodized finish and are designed for use with an M3 flat head screw.
Features:
- Aluminium anodized, silver cut highlights, and the Avid logo laser etched
- Minimal weight design, 0.3g/ea
- M3 flat head screw design to fit nearly every 8th and 10th vehicle on the market
- Available in black, blue, red, green, pink, orange, hard anodize, or purple
Includes:
- 2 x Wing Mount Buttons
- 1 x Avid Mini Decal Sheet
By adding nice silver highlights and laser etched logos they are even more desirable. The Triad button is available in a black, blue, red, green, pink, orange, hard anodize, or purple anodized finish and are designed for use with an M3 flat head screw.
Features:
- Aluminium anodized, silver cut highlights, and the Avid logo laser etched
- Minimal weight design, 0.3g/ea
- M3 flat head screw design to fit nearly every 8th and 10th vehicle on the market
- Available in black, blue, red, green, pink, orange, hard anodize, or purple
Includes:
- 2 x Wing Mount Buttons
- 1 x Avid Mini Decal Sheet
By adding nice silver highlights and laser etched logos they are even more desirable. The Triad button is available in a black, blue, red, green, pink, orange, hard anodize, or purple anodized finish and are designed for use with an M3 flat head screw.
Features:
- Aluminium anodized, silver cut highlights, and the Avid logo laser etched
- Minimal weight design, 0.3g/ea
- M3 flat head screw design to fit nearly every 8th and 10th vehicle on the market
- Available in black, blue, red, green, pink, orange, hard anodize, or purple
Includes:
- 2 x Wing Mount Buttons
- 1 x Avid Mini Decal Sheet
By adding nice silver highlights and laser etched logos they are even more desirable. The Triad button is available in a black, blue, red, green, pink, orange, hard anodize, or purple anodized finish and are designed for use with an M3 flat head screw.
Features:
- Aluminium anodized, silver cut highlights, and the Avid logo laser etched
- Minimal weight design, 0.3g/ea
- M3 flat head screw design to fit nearly every 8th and 10th vehicle on the market
- Available in black, blue, red, green, pink, orange, hard anodize, or purple
Includes:
- 2 x Wing Mount Buttons
- 1 x Avid Mini Decal Sheet
This set includes:
- Four 6x10x3mm bearings
Used when fitting the Proline Bruggy Body to the TLR 8ight-XT
These inserts are installed over the steering and throttle servo output shafts.
These are eight hole pistons, with four 1.2mm holes and four 1.3mm holes.
This set includes:
- Four 8x14x4mm Flanged Bearings
Packet includes:
- 3 x Differential Gaskets
- 6 x Differential outdrive seals
This set includes:
- Four 5x11x4mm bearings
Losi now offers a full drive pin kit which includes drive pins for the front and rear center drive shafts, front and rear axle joints, diff pins and hex pins.
This set of Gear Box Shims includes:
- 10 x 14x17x.25mm Shims
- 10 x 14x17x.10mm Shims
This is a packet of (4) 8th scale spring tubes.
Now you can get all your springs organized and kept safe so that wad of springs you have in the corner of your pit box can finally find a home.
Dimensions:
- Outside: Dia. 33.3mm X Ht. 98.6mm
- Inside: Dia. 28.4mm X Ht. 96.5mm
Package includes four upper and four lower washers that are installed on the shock shaft, above and below the shock piston.
- 1