Off-Road Nitro Kits
Further continuing with the successful SWORKz S35-4 1/8 Nitro Buggy platform, the latest S35-4 EVO is designed for an even higher level of racing.
The geometry from the worlds edition conversion kit provides optimized cornering speeds with a more easy handling feel and maximum traction.
The S35-4 EVO features a T7075 hard anodized and lightened aluminum chassis with a new short wheel base design that was tested for a long time by our factory pilots which guarantee the best speed balance for both front and rear suspensions.
HET differentials are included in the kit while the High Density Clutch Bell system are optional.
The new S35-4 EVO comes with a brand new steering Lay-Down Type Steering Bell crank servo savor system. This new Ackerman design provides the driver with better control over the S35-4 EVO buggy.
The SWORKz S35-4 EVO includes the latest Arched-Bridge-System and the higher capacity shock system. This is a big step for S35-4 EVO as it provides better stability to the buggy.
In the kit we also include special BBS pistons and oil seal parts that the worlds team drivers tested during the worlds. The parts are made by a high Precision Plastic mold machine.
Also included are specially made durable material parts for the suspension like inserts which our team drivers prefers and immediately felt more confident with them.
There are many more small changes and ideas in the new SWORKz S35-4 EVO. It is an evolution step designed and tested by the whole team that make the car even better. The secret of a modern racing car is the possibility to adapt the car setup to every track for top pilots but also have a standard setup that works on most tracks for hobby pilots. The SWORKz S35-4 EVO fulfills these two characteristics.
S35-4 EVO Pro Kit Features:
- T7075 Hard Anodized, Lightend Aluminium Chassis (New)
- Short Chassis Design (New)
- Higher Shock Towers (New)
- Longer Shock Bodies (New)
- Shorter Shock Shafts
- S35 Series BBS System Hex-Cell Shock (New)
- Shorter Front Shock Springs
- SWORKz 1/8 BBS Precision Plastic Shock Piston (New)
- Fixed Shock Spring Holder
- 3mm Updated Rear Shock Studs
- Ackerman Plate (New)
- Steering System (New)
- Servo Saver Aluminium Part (New)
- Servo Saver Plate (New)
- Servo Saver Post Locking Design (New)
- Steering Ball Studs (New)
- Steering Knuckle Plates (New)
- Updated Toe In Plates with Square Inserts (New)
- Aluminum Intensity F/F and R/F Narrow Lower Suspension Plate (New)
- New Carbon Center Diff Plate with Throttle Servo Linkage System (New)Nitro Series Center Brake Disk Holder (New)
- Lightweight Wing Mount
- SWORKz S35-4 Series Arched-Bridge-System Rear Lower Arm Set (New)
- Composite Rear Hubs with Carbon Plates
- Multi Adjustable Ball System for Rear Upper Arms
- Anticlock Screws for Shocks
- Aerodinamically Optimized Body Shell
- 3 HET Differentials Included
- 2 Front Chassis Braces Included
- Black Competition Shock Springs Included
- Adjustable Wing Position
- Adjustable Wing Angle
- More Balance Weight Positions
- Stronger Downstop Area
- Optimized Composite Material
- Aluminium Parts in T7075
Specifications:
- Length： 510mm
- Width： 308mm
- Height： 220mm
- Ground Clearance： 65mm
- Wheelbase： 325-330mm
- Track：F:304mm / R:306mm
- Gear Ratio: C:47/13T, F/R:43/13T
- Weight：3400g (Race condition)
Needed to Complete:
- .21 Class Engine
- Tuned Exhaust System
- 2-Channel Radio System
- (2) High Torque Servo
- Receiver Battery
- Glow Driver & Starting System
- Nitro Fuel & Fuel Bottle
- Paint for Polycarbonate Body
- Tyres, Wheels & Glue
NOTE: Completed vehicle shown for illustrative purposes only and is not included.
This international kit includes the N1 Body (AG‑5N0012), replacing the 6MIK body supplied with the European and United States versions.
After years of development and refinement our lowest COG design concept is enhanced even further with the production of the Agama N2. Its unique suspension creates an incredibly low COG (Centre of Gravity) race car, while our engineering teams years of experience has pushed us to ensure that not only is it fast, but it’s the easiest car to work on in its class.
Lower COG makes the N2 more consistent to drive while being able to hold higher corner speeds than your average 1/8th buggy. Its not just in the corners where the N2 excels, through bumps it stays very flat with less tendency to want to flip over and in the air the N2 flies very low and stable as its unique clean aerodynamics have a tremendous effect, working the rear wing to maximum efficiency.
SUPER EASY DIFFERENTIAL ACCESS:
The RAD (Rapid Access Diff) gearbox on the N1 creates incredibly simple diff access. The anti-roll bars and wishbones are both mounted to the lower half of the horizontally split gearbox. Making for incredibly quick and easy diff removal with the pinion gear also being accessible, allowing you to keep driveline sets together. All whilst still maintaining market leading durability and longevity through our DBS (Double Bearing System) driveline.
FULLY CONSISTENT SHOCK STROKE:
The unique, lay-down shock system on the N2 enables a non-resistant stroke through the full suspension travel of the vehicle. With little side load going through the shock shaft, you are treated to the benefit of an ultra consistent suspension feel that won’t change during long finals.
INCREDIBLY EASY TO MAINTAIN:
Maintenance has been a key consideration in the development of the N2, featuring RAD (Rapid Access Diff) access gearboxes for easy and quick diff removal in the front, centre and rear of the buggy. The amount of parts you need to remove for easy maintenance is reduced, allowing you to spend less time wrenching and more time racing. High grade metal and plastic parts are found throughout the kit making sure your car is not only fast, but durable too.
SUPER DURABLE WING MOUNT:
Molded from a new nylon material with incredible flex properties, giving the perfect balance of durability and stability for the rear wing, whilst also freeing up the rear aerodynamics of the N2.
DOUBLE BEARING SYSTEM FOR DIFFERENTIALS:
A staple in the Agama vehicle lineup, the double ball bearing system gives the buggy an incredibly free and secure drivetrain with the load for each diff being spread across 4 bearings, meaning less time re-shimming and more time on the track.
FULLY ENCLOSED WISHBONES:
New wishbones have been introduced on the N2, with an enclosed design both front and rear. Enhanced durability and adjustable flex characteristics with the removable arm stiffener. The enclosed design also makes for less dirt pick up and reduced drag on rough sections of track (and its a joy to clean).
SUPER LOW COG:
The innovative lay-down shock design and carefully positioned shock levers, not only give you an incredibly consistent and free shock stroke with no side loading, it also massively reduces the centre of gravity of the buggy, this means you can push harder on the track without the buggy getting unsettled by any bumps and ruts while maintaining a higher corner speed! Magic.
Includes:
- 1x Agama N2 Nitro Buggy Race Kit
- 1x Product Manual
Needed to Complete:
- 1x LiPo Receiver Pack
- 1x LiPo Charger
- 1x Nitro Race Fuel
- 1x Glow Driver
- 1x 2 Channel Radio (minimum)
- 2x Servos
- 1x Set of 1/8 Scale Off Road Tire
- 1x Competition .21 Engine and Exhaust Pipe
This is the new innovative N1 Nitro competition Racing Buggy from Agama.
After years of development our revolutionary design concept is finally realised with the production N1. Its unique suspension creates an incredibly low COG (Centre of Gravity) race car, while our engineering teams years of experience has pushed us to ensure that not only is it fast, but it’s the easiest car to work on in its class.
Lower COG makes the N1 more consistent to drive while being able to hold higher corner speeds than your average 1/8th buggy. Its not just in the corners where the N1 excels, through bumps it stays very flat with less tendency to want to flip over and in the air the N1 flies very low and stable as its unique clean aerodynamics have a tremendous effect, working the rear wing to maximum efficiency.
Key Features:
SUPER EASY DIFFERENTIAL ACCESS:
FULLY CONSISTENT SHOCK STROKE:
The unique, lay-down shock system on the N1 enables a non-resistant stroke through the full suspension travel of the vehicle. With no side load going through the shock shaft, you are treated to the benefit of an ultra consistent suspension feel that won’t change during long finals.
INCREDIBLY EASY TO MAINTAIN:
SUPER DURABLE WING MOUNT:
DOUBLE BEARING SYSTEM FOR DIFFERENTIALS:
FULLY ENCLOSED WISHBONES:
SUPER LOW COG:
- 1x Agama N1 Nitro Buggy Race Kit
- 1x Product Manual
Needed to Complete:
- 1x LiPo Receiver Pack
- 1x LiPo Charger
- 1x Nitro Race Fuel
- 1x Glow Driver
- 1x 2 Channel Radio (minimum)
- 2x Servos
- 1x Set of 1/8 Scale Off Road Tire
- 1x Competition .21 Engine and Exhaust Pipe
Upgrade your Agama N1 range of vehicles into the new Agama N2 specifications.
Included Parts:
| Section | Part No. | Description | QTY |
|---|---|---|---|
| Front A (Hardware) | |||
| Front A | SJG4410 | Screws 4x10 | 2 |
| Front A | SG4318 | Screws 3x18 | 2 |
| Front A | SJG4314 | Screws 3x14 | 2 |
| Front A | 0300 | 3mm nylon nuts | 5 |
| Front A | SG4312 | Screws 3x12 | 1 |
| Front B (Hardware) | |||
| Front B | SJG4305 | Screws 3x5 | 2 |
| Front B | SJG4308 | Screws 3x8 | 6 |
| Rear A (Hardware) | |||
| Rear A | SJG4418 | Screws 4x18 | 4 |
| Rear A | SJG4410 | Screws 4x10 | 2 |
| Rear A | SJG4410 | Screws 4x10 | 2 |
| Rear B (Hardware) | |||
| Rear B | SJG4310 | Screws 3x10 | 6 |
| Rear B | SJG4306 | Screws 3x6 | 2 |
| Front & Rear (Hardware) | |||
| Front & Rear | SJG4318 | Screws 3x18 | 4 |
| Front & Rear | 0300 | 3mm nylon nuts | 12 |
| Front & Rear | SG4318 | Screws 3x18 | 4 |
| Front & Rear | 8232 | Shock stand offset | 4 |
| Front & Rear | SG4325 | Screws 3x25 | 4 |
| Front & Rear | 0380 | Washer 3*8*0.7 | 4 |
| Bag 'Front' | |||
| Bag Front | 6M6004 | Front suspension mount | 1 |
| Bag Front | 6M610D | Arm link stiffener | 1 |
| Bag Front | 6M7701-N2 | Front shock tower | 1 |
| Bag Front | 6M9220 | Front body mount (carbon fiber) | 1 |
| Bag Front | 6M6202L | Front shock lower bracket L | 1 |
| Bag Front | 6M6202R | Front shock lower bracket R | 1 |
| Bag Front | 6M7202 | Front shock mount plate | 2 |
| Bag Front | 6M65880 | F&R shock springs (soft)(Blue) | 4 |
| Bag Front | 6M65875 | F&R shock springs (medium)(Green) | 4 |
| Bag Front | 5N6247e4 | Shock body | 2 |
| Bag Front | 5N8249 | Shock shaft | 2 |
| Bag 'Rear' | |||
| Bag Rear | 6M7112 | Rear camber link mount | 1 |
| Bag Rear | 6M6005 | Rear suspension mount | 1 |
| Bag Rear | 6M7113-N2 | Rear shock tower | 1 |
| Bag Rear | 6M9221E | Rear body mount (carbon fiber) | 1 |
| Bag Rear | 6M6603 | Rear shock mount plate | 2 |
| Bag Rear | 6M6203 | Rear shock lower bracket | 2 |
| Bag N2 Specific for Front | |||
| N2 Front | 9410 | 1/8 scale droop screws 4*10mm | 4 |
| N2 Front | 5N1207 | Link for stabilizer for N2 front | 4 |
| N2 Front | SK4306 | Set screw 3x6 | 2 |
| 5N826RS | Anti roll bar for N2 rear | 1 | |
| 6M1002 | Front lower arm | 1 | |
| 6M1003 | Rear lower arm | 1 | |
Requires an Agama N1/N1E to complete
This is the 1/8 Buggy Tire Bag from ProTek RC.
The ProTek RC 1/8 Buggy Tire Bag is a convenient way to haul and preserve your tires, as well as anything else that fits inside one of six included, airtight 8" tall, 4.75" diameter screw on lid storage tubes. The bag itself is made from heavy duty nylon material and measures 17" wide, 12"deep, and 9" tall.
The lid of the bag features a large ProTek RC logo in white, and has a 16x11" mesh zipper pocket on the inside providing a place to stash setup sheets, tools or other small accessories that may come in handy at the track. If you are serious about keeping your gear neat and tidy, this bag is a must have accessory.
Features:
- Perfect for 1/8 Buggy, 1/10 Short Course, No Prep/Outlaw Drag Racing, and Crawler tires smaller than 12cm
- Six airtight 20.5cm tall, 12cm diameter PET tubes with screw on lid
- Heavy duty nylon material
- Bag measures 43.5cm wide, 30.5cm deep and 23cm tall
- Internal 40.5 x 28cm mesh zippered pocket
The ProTek R/C 1/10 Buggy Carrying Bag is a clean and convenient way to transport your buggy.
Designed for racers looking for a convenient solution to transport an electric 1/10 buggy, the bag is a great way to keep your buggy from rolling around in your car or back of your truck, containing all the dirt and grime after a long day at the track. It also fits great on top of your hauler bag when loading or unloading at the track.
The ProTek R/C Carrying Bag is big enough to fit one 1/10 buggy with body and tires attached. Two durable zippers close the lid, meeting at the wing stay, leaving the wing exposed. For easy carrying, grab the wing, the side handle on the bag, or attach your own shoulder strap to the two plastic latches. The bag is also carry-on sized so it works great for plane flights.
The bag is constructed from a three-ply design, using easy-to-clean durable material on the outside and inside, with a thin layer of foam padding sandwiched between. This allows the buggy to stay safe during transport, or while stored in your workshop. At the races, roll the bag up until you need it again.
Features:
- Fits 1/10 buggies with tires on
- Contains all dirt and grime inside
- Foam padded
- Carry-on sized for flights
- Can be rolled up when not in use
- Convenient side carrying handle
- Can be used with optional shoulder strap
Specifications:
Fits: 1/10 buggy w/body and w/tires
Dimensions (W x L x H): 28 x 41 x 11cm
Fits Body: Yes
Fits Wing: Yes, but exposed
Shoulder Strap: Can be used, but is not included
NOTE: Buggy in pictures is for display purposes only and is not included.
The ProTek R/C 1/8 Buggy Carrying Bag is a clean and convenient way to transport your buggy.
Designed for racers looking for a convenient solution to transport a nitro or electric buggy, the bag is a great way to keep your buggy from rolling around in your car or back of your truck, containing all the dirt and grime after a long day at the track. It also fits great on top of your hauler bag when loading or unloading at the track.
The ProTek R/C Carrying Bag is big enough to fit one 1/8 buggy with body and tires attached. Two durable zippers close the lid, meeting at the wing stay, leaving the wing exposed. For easy carrying, grab the wing, the side handle on the bag, or attach your own shoulder strap to the two plastic latches. The bag is also carry-on sized so it works great for plane flights.
The bag is constructed from a three-ply design, using easy-to-clean durable material on the outside and inside, with a thin layer of foam padding sandwiched between. This allows the buggy to stay safe during transport, or while stored in your shop. At the races, roll the bag up until you need it again.
Features:
- Fits 1/8 buggies with tires on
- Contains all dirt and grime inside
- Foam padded
- Carry-on sized for flights
- Can be rolled up when not in use
- Convenient side carrying handle
- Can be used with optional shoulder strap
Specifications:
Fits: 1/8 buggy w/body and w/tires
Dimensions (W x L x H): 34 x 45.5 x 14.5cm
Fits Body: Yes
Fits Wing: Yes, but exposed
Shoulder Strap: Can be used, but is not included
NOTE: Buggy in pictures is for display purposes only and is not included.
The ProTek R/C 1/8 Truggy Carrying Bag is a clean and convenient way to transport your truggy.
Designed for racers looking for a convenient solution to transport a nitro or electric Truck, this bag is a great way to keep your Truck from rolling around in your car or back of your truck, containing all the dirt and grime after a long day at the track. It also fits great on top of your hauler bag when loading or unloading at the track.
The ProTek R/C Carrying Bag is big enough to fit one 1/8 Truggy with body and tires attached. Two durable zippers close the lid, meeting at the wing stay, leaving the wing exposed. For easy carrying, grab the wing, the side handle on the bag, or attach your own shoulder strap to the two plastic latches. The bag is also carry-on sized so it works great for plane flights.
The bag is constructed from a three-ply design, using easy-to-clean durable material on the outside and inside, with a thin layer of foam padding sandwiched between. This allows the Truggy to stay safe during transport, or while stored in your shop. At the races, roll the bag up until you need it again.
Features:
- Fits 1/8 buggies with tires on
- Contains all dirt and grime inside
- Foam padded
- Carry-on sized for flights
- Can be rolled up when not in use
- Convenient side carrying handle
- Can be used with optional shoulder strap
Specifications:
Fits: 1/8 truggy w/body and w/tires
Dimensions (W x L x H): 44.5 x 53.5 x 12cm
Fits Body: Yes
Fits Wing: Yes, but exposed
Shoulder Strap: Can be used, but is not included
NOTE: Truggy in pictures is for display purposes only and is not included.
The ProTek R/C Starter Box Carrying Bag is safer and more convenient for carrying a roaring 1/8 scale nitro Truggy to and from the pits, with straps optimized for truggy use.
Truggy tires spinning at several thousand RPMs are dangerous, especially when they’re just a couple of inches from your arm while you’re balancing the truck atop the starter box. Not to mention, the fumes that smack you in the face with every rev of the engine. ProTek R/C’s Starter Box Carrying Bag allows you to comfortably carry your nitro truggy at your side when moving in and out of pit row. The Carrying Bag also frees up your other hand while putting the weight of the truggy and starter box much lower in a more natural position - your arm will thank you!
The all canvas Starter Box Carrying Bag features an interior liner and two handle straps designed not to interfere with truggy tires. The front straps are also attached close to the corner to stay clear of the pipe stinger. Inside the bag, the liner is fuel resistant and easily cleans up when things get messy.
The carrying bag will accommodate most popular starter boxes including: ProTek R/C SureStart, OFNA 1/10 & 1/8 starter boxes, Mugen Seiki Pro Starter BIII, LRP 1/10 & 1/8 Spec 2, Hudy “Star-Box”, Team Associated Compact 1/10 & 1/8 starter boxes and Team Losi 8IGHT & 8IGHT-T starter boxes. Make it easy on your pit guy and grab a ProTek R/C Starter Box Carrying Bag.
Features:
- Durable, heavy-duty bag material
- Dual handles won't interfere with tires
- Safe, one handed pit operation
- Straps optimized for truggy use
- No fumes in your face
- Compatible with boxes up to 14cm wide x 36.8cm long
- Made in the USA
Compatible Starter Boxes:
PTK-4500: ProTek R/C "SureStart"
TLR99059: TLR 8IGHT/8IGHT-T
HUD104500: Hudy "Star-Box"
OFN10244: OFNA Truggy Box
OFN10245: OFNA 1/10 & 1/8
LRP37101: LRP 1/10 & 1/8 Spec 2
MUGB0237: Mugen Pro Starter BIII
ASC1751: Team Associated Compact 1/10 & 1/8
NOTE: Truggy in pictures is for display purposes only and is not included.
This is the Pro Pit Pack from ProTek RC.
Designed for racers and mechanics alike, this versatile pack ensures that your essential tools and accessories are organized and easily accessible during pit stops. Whether you're at the track or in the workshop, the Pro Pit Pack keeps everything you need within reach, allowing for quick and efficient adjustments.
Constructed from heavy-duty fabric, this pack is built to withstand the rigors of the racing environment. Its compact design makes it easy to carry, while a zippered compartment and elastic straps securely hold your tools, ensuring nothing is left behind. The zippered pouch is perfect for storing small parts like glow plugs, and the additional elastic straps behind the zippered pouch are ideal for items like tuning screwdrivers or glow igniters. With belt clips included, this is a must have for any racer!
Features:
- Compact design for easy portability
- Durable construction to withstand tough conditions
- Multiple compartments for organized storage
- Elastic straps to securely hold tools in place
- Zippered pouch for small part storage
This is the Fuel Gun and Bottle Holster from ProTek RC.
This innovative and handy accessory allows you to securely carry your fuel gun and bottle, making it easy to access during races and practice sessions. No more fumbling around searching for your fuel bottle or gun, give yourself the holster the pro's use and dominate pit lane!
Note: This holster fits most fuel bottles and guns but may not be compatible with every option available. We recommend the ProTek RC "Fast Fill 2" fuel bottle (PTK-7606) and the ProTek RC "Quick Pit 2" Dump Fuel Gun (PTK-7608) for proper fitment.
Features:
- Securely holds fuel gun and bottle
- Convenient for quick access during races
- Durable construction for long-lasting use
- Secure belt loop and thigh strap mounting
- Pair with the ProTek RC Pro Pit Pack (PTK-8125) for the ultimate pit stop experience!
- Holds both a fuel bottle Fuel Gun
- 1