Brushed Motors
Features include:
- This versatile motor features torque ideally suited to off-road cars.
- It utilizes brush damper, terminal heat sink, and chip condenser components.
- A sponge cover is included to protect the motor.
- The gun metal color can has slits to help heat dissipate.
- Features a blue anodized end bell.
- Input voltage: 7.2V
- RPM (without load): 26,500
- Maximum torque: 49mN-m (7.2V)
- Use ball bearings when installing this motor.
- XV-01 series chassis will require motor extension cables.
Features include:
- Input voltage: 7.2-8.4V
- RPM (without load): 26,500
- Maximum torque: 500gf-cm (at 7.2V)
- 23T
• Features optimum power output for direct-drive 2WD chassis such as F103 & F104.
• Compatible with Item 53581 Racing Motor Brush Set (Standard Type).
• The motor produces 14,000 rpm and 39mN/m of torque (7.2V).
Features include:
- Input voltage: 7.2-8.4V
- RPM (without load): 14,000
- Maximum torque: 39mN/m of torque (at 7.2V)
- 32T
The G2X is a nice easy upgrade to the standard 27 Turn brushed motor found in a lot of Tamiya and Kyosho RC kits.
The Tamiya RS-540 sport tuned motor is an economical high performance motor for on-road and off-road vehicles.
It will work in many Tamiya vehicles (check instruction manual for applications.)
Specifications:
Usable Voltage: 6-8.4V (5-7 cells)
RPM at Best Efficiency: 18,300 RPM (7.2v)
Torque at Best Efficiency: 350g/cm (7.2v)
peak rpm: 21,000
Current drain at best efficiency: 12A (7.2v)
Peak Current Draw: 50+A
The closed end bell design, low maintenance and factory installed wires make it an easy to operate and install option.
Specifications:
Type: Brushed
Size: 540
Bearings or Bushings: Bushing
# of Turns/Windings: 20T
Timing: No
Voltage: 4.8 - 9.6V
Cells: 4-8 Ni-Cd/Ni-MH or 2S Li-Po
Overall Diameter: 36mm
Shaft Diameter: 3.175mm
Shaft Length: 15.5mm
Overall Length: 50mm
a 550 Motor is the same diameter as a 540 motor however the can is longer and therefore will not fit as a replacement in certain applications.
The closed end bell design, low maintenance and factory installed wires make it an easy to operate and install option.
Specifications:
Type: Brushed
Size: 550
Bearings or Bushings: Bushing
# of Turns/Windings: 15T
Timing: No
Voltage: 4.8 - 9.6V
Cells: 4-8 Ni-Cd/Ni-MH or 2S Li-Po
Overall Diameter: 36mm
Shaft Diameter: 3.175mm
Shaft Length: 15.5mm
Overall Length: 57mm
Compared to a standard Type 540 motor, it offers a higher top speed and improved acceleration when used with RC car models with standard gear ratios.
It will work in many Tamiya vehicles (check instruction manual for applications.)
Specifications:
Usable Voltage: 6.6-7.2V
RPM at Best Efficiency: 16,000 RPM (7.2v)
Torque at Best Efficiency: 305g/cm (7.2v)
Current drain at best efficiency: 10A (7.2v)
These are ideal for basic radio control vehicle use. Features factory installed motor wires with bullet connectors.
The closed end bell design, low maintenance and factory installed wires make it an easy to operate and install option.
Specifications:
Type: Brushed
Size: 540
Bearings or Bushings: Bushing
# of Turns/Windings: 15T
Timing: No
Voltage: 4.8 - 9.6V
Cells: 4-8 Ni-Cd/Ni-MH or 2S Li-Po
Overall Diameter: 36mm
Shaft Diameter: 3.175mm
Shaft Length: 15.5mm
Overall Length: 50mm
This is packet of (10) Tamiya Snap Connectors For 540 Brushed Motor.
This RC Snap Connector Set is used for Tamiya cars that come with 540, brushed type electric motors, and ESC's (Electronic Speed Controls), but can also be used on other brand motors.
The connectors in this set can be used to replace worn out connectors.
Key Features:
- For: 540 Brushed Motor
- Material: Metal / Rubber
- Color: Silver
What's In The Box?
- 10 Male connectors
- 10 Male rubber boots
- 10 Female connectors
- 10 Female rubber boots
- 1